Jalopnik 
Enter your username and password.
Detroit, 2:38 AM
Mon Nov 30
13 posts in the last 24 hours
Tip your editors:
tips@jalopnik.com
Editor-in-Chief:
Ray Wert | Email | AIM
Road Test Editor:
Wes Siler | Email
Weekend Editor:
Murilee Martin | Email
Associate Editor - Houston:
Matt Hardigree
Associate Editor - Detroit:
Ben Wojdyla
Editor-at-Large:
Mike Spinelli
Contributors:
Mark Arnold
John Krewson | Email
Andy Didorosi
Original material is licensed under a Creative Commons License permitting non-commercial sharing with attribution.
11/29/09
11/29/09
11/29/09
11/29/09
While LeMons cars might be "cheap race heaps" there is no excuse to be "cheap" on safety. Every bit of safety equipment on all LeMons race cars must be held to the highest possible standard of safety..
Every LeMons race team and driver must ask what are their drivers life worth... Was it worth saving those few bucks to install anything less than the best in safety for your LeMons racer if an airborne moment similar to what happened to this MGB killed the driver and cause injury to your fellow LeMons racers worth pinching pennies?
LeMons racing is serious business, take every aspect of safety very, very seriously...
11/29/09
A) Autopower roll cage. B) Experienced cage welder. C) Nothing cheap about it.
I was cheap on the car, but spent a boatload on the best safety gear and resent your assumptions.
The failures concern me too. It DID however survive THREE flips. I will take what was learned and improve the next cage.
11/29/09
With a few notable (and annoying) exceptions, people at LeMons DO take safety seriously. That's why safety items aren't included in the $500 limit.
11/29/09
Everything can always be stronger, but there are practical limits. I'd say the cage performed very well.
But it points up an issue for folks using clapped out econocars - the underlying structure, and all it's finite element pieces, only have so much gumption, before they get stressed from twenty years of hard use and have largely rusted away.
01:59 AM
$$$$$ spent or "experienced cage welder" does not mean a safe cage. IMO, any bolt in cage is questionable.
Bolt in means loading what is basically 0.035" thick sheet metal with several thousands pound of force in a small area. It will fail... the real questions is how bad will the failure be.
You may resent what I say about the roll cage in that MGB, my point is do what ever it takes to make DAM SURE that roll cage is will not fail. You're lucky to have survived that triple flip without serious unjury, but what if the MGB flipped over more than that and the car ended up on track upside down and nailed by more than one other LeMons race car directly on the cage with torn sheet metal anchor plates and broken welds?
Possible yes, and the results could have been less pretty.
Again, what is your life worth?
11/28/09
Next time you might want to tune your aero package a little more.
11/28/09
11/28/09
[www.flickr.com]
and
[www.flickr.com]
I have a feeling last weekend's rollovers will quiet down the people who have been whining about the roll cage regulations on the LeMons forum.
11/28/09
11/28/09
As for the pictures themselves: Yikes. Damned lucky that the car didn't take just one more tumble after the cage was compromised. I don't reckon that landing on the roof with an already cracked roll cage would have ended as well.
Glad everyone is alright.
11/28/09
11/28/09
11/28/09
11/28/09
11/28/09
Back to you in the studio, Stud Beefpile.
11/28/09
Maybe this is just the setup for Elin's new book about working on your backswing?
11/28/09
11/28/09
11/28/09
Always reverse park into your driveway, that way when you have to GO....
11/28/09
the PGA tour. HA!
11/28/09
11/28/09